Demilec Insulation Removal & Replacement Nationwide

Demilec Insulation Removal & Replacement in Torrance: What to Know First

We provide independent Demilec insulation removal and replacement in Torrance, with most jobs completed in one to two days and a written price delivered before any work starts. As an independent Demilec service provider, we handle the full line of Demilec spray foam and hybrid systems found in South Bay homes, including jobs where the original product has degraded, been contaminated, or was installed over an unsealed attic floor. Typical turnaround from signed scope to final walkthrough runs 48 to 72 hours for standard attic removals, though vermiculite or heavily degraded foam adds time for safe handling protocols. This page is for Torrance homeowners who see settling, odor, or thermal loss in a Demilec-insulated space and want a documented, priced solution without the runaround. Call (424) 704-9866 for a free estimate and a written scope you can compare.

Call (424) 704-9866

How Demilec Products Fail - and How We Fix Them

• Heatlok HFO High Lift settling in coastal Torrance attics. The high-lift chemistry can shrink 10-15% over five to seven years when installed over warm, humid roof decks common in the Hollywood Riviera and Southwood neighborhoods. We remove the degraded layer, seal top plates and can lights with closed-cell foam, then replace with a system matched to your ventilation profile.
• Heatlok XT off-gassing in enclosed rafter bays. XT series installed in 2016-2019 cathedral ceilings sometimes retains amine catalyst odor when the mix ratio drifted during application. We ventilate, remove affected foam, and re-blow with a neutral-cure alternative - usually Johns Manville or Knauf blown-in behind baffles - so the bedroom below stops smelling like a chemical plant every summer afternoon.
• Demilec open-cell in floor joists absorbing crawl space moisture. Sealection 500 in vented crawl spaces wicks groundwater vapor in the Old Torrance basin near the marshlands, collapsing R-value and supporting mold. We pull the saturated foam, lay polyethylene vapor barrier, then replace with Rockwool Comfortbatt - hydrophobic, vermin-resistant, and better suited to that microclimate.
• Hybrid jobs where Demilec foam was sprayed over fiberglass with no air sealing. We see this in Rancho Palos Verdes-adjacent builds from the late 2010s: shiny Demilec layer on top, leaky bottom, thermal bridging everywhere. We strip both layers, run a blower-door depressurization test to establish CFM50 baseline, seal every penetration, then rebuild the stack with documented R-values.
• Contaminated Demilec from rodent intrusion in unsealed attics. Once mice tunnel through open-cell, the foam traps urine and organic matter; no cleaning saves it. We remove, sanitize the deck, rodent-proof with steel mesh and foam at all entry points, then reinsulate - usually with GreenFiber cellulose treated with borate, which rodents won’t nest in.

Our Demilec Insulation Removal & Replacement Process

1. 1
   Call and scope. A live person answers 24/7. We schedule a site visit, and Wes Okafor or a named technician arrives with a camera, moisture meter, and blower-door rig.
2. 2
   Diagnostics and documentation. We run the blower-door depressurization test - a diagnostic that measures how much conditioned air a house leaks per hour - to establish CFM50 baseline. Photos of every penetration, stain, and degraded foam section go into your file before a tool comes out of the truck.
3. 3
   Written price and material selection. You get a flat price, written scope, and written warranty before anyone lifts a tool. For Demilec replacements, we specify OEM-compatible or quality aftermarket materials from our roster: Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, or GreenFiber. No proprietary lock-in.
4. 4
   Removal and air sealing. Demilec foam comes out with controlled cutting and HEPA extraction. We seal top plates, can lights, plumbing stacks, and electrical penetrations with closed-cell foam or acoustical sealant - depending on what’s code-compliant for your assembly.
5. 5
   Replacement, testing, and handoff. New insulation goes in. We run the blower-door test again and publish your before-and-after CFM50 numbers. You walk away with a written pre- and post-job report: R-values achieved, CFM50 readings, and photos of every sealed penetration. The 365-Day Done Right Promise applies from day one.

What Demilec Insulation Removal & Replacement Costs in Torrance

Most Demilec insulation removal and replacement jobs in Torrance run between $3,200 and $7,800 for a single attic or crawl space, depending on what we find. Here’s how the price breaks:

• Standard open-cell removal and replace with blown-in cellulose: $3,200-$4,800 (1,200-2,000 sq ft attic, accessible hatch, no hazmat)
• Closed-cell Demilec removal with full air sealing and Rockwool replacement: $5,500-$7,800 (denser material, longer cut-out time, more disposal weight)
• Contaminated foam with rodent sanitation and proofing: add $800-$1,400 to base removal
• Vermiculite under or adjacent to Demilec layers: $8,500-$14,000 (third-party lab testing, abatement protocol, re-inspection)

What moves the price: roof pitch over 8/12, limited attic access requiring deck removal, active moisture intrusion needing source repair, and the square footage of foam installed. We also service Reflectix systems when radiant barriers are part of the rebuild. Call (424) 704-9866 for an exact quote - estimates are free, and we deliver a written price before any work starts.

Why Torrance Homeowners Call Topside Attic Insulation Torrance for Demilec Work

We’ve sealed and insulated over 9,000 homes since 2016, and a steady run of those have been attic retrofits in the Del Amo neighborhood here in Torrance. Our technicians know the difference between Heatlok HFO and Heatlok XT failure signatures without pulling out a manual. Every job gets the Haven Standard treatment: written price first, documented photo record last, and before-and-after blower-door numbers on any air-sealing scope. If something’s not right, the 365-Day Done Right Promise means we make it right - no voicemail loops, no callback windows measured in business days. And because we source from eight major manufacturers including Demilec and Reflectix, we specify what’s appropriate for your assembly, not what moves our inventory.

Seal the leaks first. The insulation’s just holding the work in place.

FAQs